Cabling testing and certification. Every link. Every time.
We test and certify structured cabling installations across the UK using Fluke DSX analysers for copper and OTDR equipment for fibre. Full certification reports provided on completion. Manufacturer warranty supported.
Comprehensive testing for every type of structured cabling installation.
From Fluke DSX copper certification to OTDR fibre testing, we provide the full range of structured cabling testing services required to certify installations and support manufacturer warranty claims.
Fluke DSX Copper Testing
Every copper link tested with a Fluke DSX cable analyser to the relevant standard. Cat6, Cat6A, and Cat7 all supported. Pass or fail results for every parameter including insertion loss, NEXT, FEXT, return loss, and propagation delay.
OTDR Fibre Testing
Every fibre link tested with an OTDR from both ends. Splice losses, connector losses, and total link loss all measured and recorded. Reflections and faults identified and located. Full OTDR trace reports provided.
Certification Report Production
Full certification reports produced for every project. Reports include pass or fail results for every link, test parameters, equipment used, and tester identification. Reports provided in PDF and electronic format.
Manufacturer Warranty Support
Certification reports produced in the format required by cabling manufacturers to support warranty registration. Warranty registered on your behalf at project completion. Warranty documentation provided.
Third-Party Certification
Independent testing and certification of cabling installed by others. Useful for verifying the quality of existing installations, supporting warranty claims, or providing evidence for compliance purposes.
Fault Finding and Remediation
Failed links investigated and faults located using the test equipment. Common faults including split pairs, crossed pairs, open circuits, and high insertion loss all diagnosed and resolved. Re-tested after remediation.
From test plan to certified documentation and warranty.
Test Plan Preparation
Test plan prepared before testing begins. Every outlet identified and numbered. Test parameters confirmed for the cabling standard being tested. Equipment calibration verified and recorded.
Copper Link Testing
Every copper link tested with the Fluke DSX analyser. Both ends of each link tested. Results reviewed immediately. Any failures investigated and the cause identified before moving to the next link.
Fibre Link Testing
Every fibre link tested with the OTDR from both ends. Splice losses, connector losses, and total link loss measured and compared against the design budget. Any failures investigated and resolved.
Fault Investigation and Remediation
Any failed links investigated using the test equipment to locate the fault. Faults remediated by re-terminating, re-splicing, or replacing the affected cable section. Links re-tested after remediation.
Report Production
Full certification reports produced covering every link. Reports include all test results, equipment details, and tester identification. Reports reviewed for completeness before being provided to the customer.
Warranty Registration
Certification reports submitted to the cabling manufacturer to support warranty registration. Warranty registered on the customer's behalf. Warranty documentation provided as part of the project handover pack.
How we have helped UK organisations with cabling certification.
New Installation Certification
A Glasgow law firm had a new Cat6A structured cabling installation completed by a local contractor. They needed independent certification to support the manufacturer warranty claim and satisfy their IT auditors.
Independent Fluke DSX testing completed on all 96 outlets. 4 failed links identified and remediated by the original contractor. Full certification report produced. 25-year manufacturer warranty registered successfully.
Legacy Installation Audit
A Cardiff NHS trust needed to verify the performance of structured cabling installed 8 years ago before deploying new clinical systems that required guaranteed 1Gbps connectivity to every outlet.
Fluke DSX testing completed on all 240 outlets. 18 outlets failed due to age-related degradation and were replaced. Full certification report produced. Clinical system deployment proceeded with confidence.
Warranty Claim Support
An Edinburgh university was experiencing intermittent network performance issues on a recently installed structured cabling system. The installer disputed the fault was in the cabling.
Independent OTDR and Fluke DSX testing completed. 12 links identified with marginal performance. Test reports provided as evidence for the warranty claim. Installer replaced all affected links under warranty.
Get your cabling tested and certified with a fixed-price quote within 48 hours.
Tell us how many outlets you need tested and we will provide a fixed-price quote for Fluke DSX or OTDR testing with full certification reports. No hidden extras.